Glossary
of Watch Terms
These
words are used frequently in watch terminology. Refer to the following
definitions if you have any questions about technical specifications
or terms.
A
Accuracy:
Refers to rate constancy of a watch, not only on whether it is showing
the exact time. A watch gaining or loosing exactly the same amount
every day is considered accurate.
Acrylic
Crystal:
Sometimes referred to as Hesolite, an acrylic crystal is composed
of plastic composite that is generally less expensive and less durable
than a sapphire or a mineral crystal. The benefits of an acrylic
crystal are that it flexes rather than shatters on impact. It also
produces little glare under bright light and can be polished easily.
Alarm:
A device that makes a sound at a preset time. There are both quartz
and mechanical alarm watches.
Altimeter:
Function that provides altitude by responding to changes in barometric
pressure, commonly found in pilot watches. Inside a pressurized
airplane cabin, the altimeter registers as if on land.
Analog
Watch:
A watch with a dial, hands, and numbers or markers that present
a total display of 12-hours.
Analog-Digital
Display:
A watch that shows the time by means of hands (analog display) as
well as by numbers (a digital display). The analog display has a
traditional dial with hour, minute and sometimes second hands. The
digital display shows the time numerically with a liquid crystal
display. This feature is usually found on sport watches.
Annual
Calendar:
A watch showing the day, date month and 24 hours, adjusting automatically
for short and long months. The calendar needs setting only once
a year - at the end of February to the 1st of March.
Aperture:
Small opening. The dials of some watches (in French: montres à
guichet) have apertures in which certain indications are provided
(e.g. the date, the hour, etc).
Atmosphere (Atm):
Unit of pressure used in watch making to indicate water resistance.
Atomic
Time Standard:
Provided by the U.S. National Institute of Standards and Technology,
Time and Frequency Division, Boulder, Colorado, atomic time is measured
through vibrations of atoms in a metal isotope that resembles mercury.
The result is extremely accurate time that can be measured on instruments.
Radio waves transmit this exact time throughout North America and
some 'atomic' watches can receive them and correct to the exact
time. To synchronize your watch with atomic standard time, call
(303) 499-7111.
Automatic
Movement / Automatic Winding (also called self-winding):
A mechanically powered watch that is wound by the motion of the
wearer's arm rather than through turning the winding stem (manual
mechanical). In response to this motion, a rotor turns and winds
the watch's mainspring. Most automatic watches have up to 36 hours
of power reserve. If an automatic watch is not worn for a day or
two, it will wind down and need to be wound by hand to get it started
again.
Main
Menu
B
Band:
A vague, generic term used to refer to the band that holds a watch
on your wrist. The preferred terms bracelet and strap, clearly describe
the two major types.
Battery
EOL:
Battery End Of Life indicator. This function forewarns of impending
battery failure in a quartz watch by means of the second hand jumping
in two or sometimes four-second intervals. The wearer usually has
approximately two weeks before battery failure.
Battery
Life:
The period of time that a battery will continue to provide power
to run the watch. Life begins at the point when the factory initially
installs the battery in the watch.
Battery:
A device that converts chemical energy into electricity. Most watch
batteries are the silver oxide type, delivering 1.5 volts. Much
longer-lasting lithium batteries deliver 3 volts.
Battery-less
Quartz:
Also known under various marketing names, including Kinetic (Seiko),
Omega-matic (Omega), and Auto quartz (Invicta). Terms for the modern
hybrid watch technology of using a quartz movement powered by a
small electric current generator operated by a rotor. Electricity
generated from the rotor's movement is stored in a capacitor, rechargeable
battery, or similar means to keep the watch running. So, like an
automatic watch, these also must be worn regularly to keep up their
electrical power reserve.
Bezel:
Generically, the upper part of the watch body. Specifically, it
usually refers to a ring around the outside of the crystal. On jewelry
watches, the bezel may contain a ring of diamonds. On sports watches,
the bezel may have calibrated markings and the ability to rotate
in one or two directions.
Bidirectional
Rotating Bezel:
A bezel that can be moved either clockwise or counterclockwise.
These are used for mathematical calculations or for keeping track
of elapsed time.
Bracelet:
A bracelet is the flexible metal band consisting of assembled links,
usually in the same style as the watchcase. Detachable links change
the length of the bracelet. Bracelets can be made of stainless steel,
sterling silver, gold, or a combination. See also strap.
Main
Menu
C
Cabochon:
Used to indicate a smooth round or oval convex shaped polished gemstone.
In watch terminology, it describes a decorative stone set in the
watch crown.
Calendar:
The calendar mechanism or function on a watch can consist of a date
only showing in a window through to a triple calendar, showing the
date, day and month. A combination of dial cut outs and pointer
hands may be used. The most complicated calendar mechanisms may
be mechanically programmed to show the year and months including
those with less that 31 days; leap years can also be mechanically
allowed for. Sometimes referred to as a perpetual calendar.
Case
or Watchcase:
The metal housing that contains the internal parts of a watch. Stainless
steel is the most typical metal used, but titanium, gold, silver
and platinum can also be used.
Chronograph
Rattrapante:
The addition of a flyback hand (rattrapante) significantly increases
the potential uses for chronographs. It makes possible the measurement
of split second times or timing simultaneous events of unequal duration.
Chronograph:
A multifunction sport watch with a stopwatch function. Most have
two or three subdials, or minidials, for measuring minutes and hours.
When used in conjunction with specialized scales on the watch dial
it can perform many different functions, such as determining speed
or distance ( see "tachometer" and "telemeter").
Some can time more than one event at a time (see "flyback hand"
and "split seconds hand"). Do not confuse with "chronometer"
which is a timepiece that has met certain high standards of accuracy
set by an official watch institute of Switzerland.
Chronometer:
This term refers to a precision watch that is tested in various
temperatures and positions, thus meeting the accuracy standards
set by C.O.S.C. in Switzerland. These watches are provided with
a chronometer certifcate detailing specific test results by the
C.O.S.C.
Clasp:
The attachment used to connect the two ends of the watch bracelet
around the wrist.
C.O.S.C.:
Control Officile Suisse de Chronometers or Swiss Controle Officiel
des Cronometres- the independent Swiss regulatory organization that
rigorously tests and certifies (or fails) watch movements for chronometer
status.
Countdown
Timer:
A function that lets the wearer keep track of how much of a preset
period of time has elapsed. Some countdown timers sound a warning
signal a few seconds before the time runs out. These are useful
in events such as yacht races, where the sailor must maneuver the
boat into position before the start of a race.
Crown:
The crown often referred to as the winding crown or winder is used
for winding the watch in the case of a non-automatic, for setting
the hands to the correct time and often for setting the date in
the case of calendar equipped watches. On diving/sports models,
the crown may be screw-down whereby it screws onto a threaded tube,
which protrudes from the case of the watch. This often ensures superior
water resistance.
Crystal:
The cover over the watch dial is called the crystal. There are three
types of crystals commonly used in watches: acrylic crystal is an
inexpensive plastic that allows shallow scratches to be buffed out.
Mineral crystal is composed of several elements that are heat-treated
to create an unusual hardness that aids in resisting scratches.
Sapphire crystal is the most expensive and durable, approximately
three times harder than mineral crystals and 20 times harder than
acrylic crystals. A non-reflective coating on some sport styles
prevents glare.
Crystal
Skeleton Caseback:
Caseback made of transparent material such as hardened mineral crystal
or sapphire crystal that reveals the intricate movement of the watch.
Cyclops
(Magnified Window):
A small window or lens in the crystal that is added to magnify the
date 2 1/2 times.
Main
Menu
D
Day/Date
Watch:
A watch that indicates not only the date but also the day of the
week.
Deployment
Buckle (Foldover):
A three-folding enclosure that secures the two ends of the bracelet
and allows enough room for placing the watch on the wrist when fully
deployed. When closed, the buckle covers the two-piece folding mechanism.
Depth
Alarm:
An alarm on a diver's watch that sounds when the wearer exceeds
a preset depth. In most watches it stops sounding when the diver
ascends above that depth.
Depth
Sensor/Depth Meter:
A device on a diver's watch that determines the wearer's depth by
measuring water pressure. It shows the depth either by analog hands
and a scale on the watch dial or through a digital display.
Dial:
The dial, often referred to as the face is usually marked with numbers
or batons to which the hands point in order for the wearer to tell
the correct time. Dials may be minimalist, with no markers at all,
or extremely complex as in the case of pilots' chronographs. Dials
may be decorated with patterns or in some cases with precious stones.
Digital:
The display of time in numbers instead of hands on the dial. The
numbers can appear in an LCD (Liquid Crystal Display), which shows
a continuous reading or an LED (Light-Emitting Diode), which shows
the time at the push of a button.
Display:
Indication of time or other data, either by means of hands moving
over a dial (analog display) or by means of numerals appearing in
one or more windows (digital or numerical display); these numerals
may be completed by alphabetical indications (alphanumerical display)
or by signs of any other kind. Example: 12.05 MO 12.3 = 12 hours,
5 minutes, Monday 12th March. Such displays can be obtained by mechanical
or electronic means.
Diver's
Watch:
Divers' watches traditionally feature a graduated, rotating bezel,
screw down winding crown, and caseback... must be water resistant
to at least 200m or 660 feet.
Dual
Time/Second Time Zone Bezel:
A rotating bezel, which can be used to display a separate time zone
distinct from that shown on the dial.
Dual
Time:
A watch that measures current local time as well as at least one
other time zone. The additional time element may come from a twin
dial, extra hand, subdial, or other means.
Main
Menu
E
Elapsed Time Rotating Bezel:
A graduated rotating bezel (see "rotating bezel") used
to keep track of periods of time. The bezel can be turned so the
wearer can align the zero on the bezel with the watch's seconds
or minutes hand. You can then read the elapsed time off of the bezel.
This saves from having to perform the subtraction that would be
necessary if you used the watch's regular dial.
Elapsed
Time:
The actual time taken for an object to travel over a specified distance.
Engine
Turning:
Decorative engraving, usually on a watch dial.
EOL:
End of Life. In quartz movement, the end of battery life is indicated
by the second hand, which starts to jump every four seconds. The
battery should be changed immediately.
Main
Menu
F
Face:
The visible side of the watch or the dial.
Flyback:
An additional hand on a chronograph which moves with the second
hand but, can be stopped independently to measure an interval which
can then "fly back" to catch up with the other hand. This
is useful for capturing lap times without losing the ability to
capture the finish time.
Foldover
Buckle (Deployment):
A three-folding enclosure that secures the two ends of the bracelet
and allows enough room for placing the watch on the wrist when fully
deployed. When closed, the buckle covers the two-piece folding mechanism.
Main
Menu
G
Gasket:
A rubber or plastic ring that seals the internal works of the watch
against dust, moisture and water.
GMT
Timezone:
GMT (Greenwich Mean Time), also known as Zulu Time, as set to the
international clock in Greenwich, England, reflects, through an
additional hour hand, the world time on a 24-hour scale and is used
by pilots worldwide.
Gold
Plating:
An application of gold over the surface of an item.
Gold,
Rose Gold, Yellow Gold, and White Gold:
The only natural form of gold is yellow gold. But since gold is
too soft in its pure form to make jewelry, it is normally made into
an alloy by mixing it with other metals. The portion of pure gold
to other metals determines the Karat rating. 24K is pure gold. 18K
is 75% pure. The exact nature of the other metals used determines
the color. A moderate amount of copper in the alloy creates Rose
Gold. A moderate amount of palladium and nickel creates white gold.
Main
Menu
H
Hand:
Indicator, usually made of a thin, light piece of metal, variable
in form, which moves over a graduated dial or scale. Watches usually
have three hands showing the hours, minutes and seconds.
Handwinding
(Manual Mechanical):
A watch with a manual mechanical movement, which needs to be wound
by the wearer using the winding crown. This winds the mainspring
up which then releases its energy to power the watch.
Main
Menu
J
Jewels:
The bearing, endstone or pallet used for reducing friction within
the movement of a watch are made of synthetic material of precious
or semi-precious stones. Usually a very inexpensive form of synthetic
ruby, these are used for virtually frictionless pivots or hubs at
certain critical places in the watch mechanism. These jewels do
not add any monetary value to a watch. It is also important to understand
that more jewels does not necessarily make a better watch.
Jump
Hour Indicator:
A jump hour indicator takes the place of an hour hand. It shows
the hour by means of a numeral in a window on the dial of the watch.
The word "jump" refers to the fact that the numerals jump
from 1 to 2 to 3, etc., rather than showing intermediate times between
hours as hour hands do. The minutes and seconds in a jump hour watch
are read as normal from the analog hands and dial.
Main
Menu
K
Karat or K:
An indication of the purity of the metal used, expressed in the
number of 1/24th of the pure metal used in the alloy. Metals such
as gold are too soft in their pure state use in jewelry, so they
are typically made into an alloy with other metals for strength.
24K (equal to 24/24ths) is pure metal. 18K is 18 parts pure metal
mixed with 6 parts of other metals. That translates to 18/24=0.750,
which is 75% pure, or 750 parts per thousand.
Kinetic:
Refers to the Seiko line of Kinetic watches. This innovative technology
has a quartz movement that does not use a battery. Movement of your
wrist charges a very efficient capacitor which powers the quartz
movement. Once the capacitor is fully charged, men's models will
store energy for 7-14 days without being worn. Ladies models store
energy for 3-7 days. The watch alerts you to a low capacitor charge
when the seconds hand starts to move in two second intervals.
Main
Menu
L
Lap Memory:
The ability, in some quartz sport watches, to preserve in the watch's
memory the times of laps in a race that have been determined by
the lap timer (see "lap timer"). The wearer can recall
these times on a digital display by pushing a button.
Lap
Timer:
A chronograph function that lets the wearer time segments of a race.
At the end of a lap, the wearer stops the timer, which then returns
to zero to begin timing the next lap.
LCD
Display (Liquid Crystal Display):
A digital watch display that shows the time electronically by means
of a liquid held in a thin layer between two transparent plates.
Followed from the earlier LED or Light Emitting Diode display of
the first quartz digital watches. The LCD was preferred as it used
vastly less power than the LED thus the time could be shown constantly
as opposed to having to press a button for time display.
Lugs:
Extensions on both sides of the case where the bracelet or strap
is attached.
Main
Menu
M
Magnified Window (Cyclops):
A small window or lens in the crystal that is added to magnify the
date 2 1/2 times.
Manual
Winding:
Refers to a watch with a manual mechanical movement, which needs
to be wound by the wearer using the winding crown. This winds the
mainspring up which then releases its energy to power the watch.
Mechanical
Movement:
A movement based on a mainspring which when wound slowly unwinds
the spring in an even motion to provide accurate timekeeping. As
opposed to a manual mechanical watch which needs to be wound on
a consistent basis, an automatic mechanical requires no winding
because of the rotor, which winds the mainspring every time you
move your wrist (see our section on automatic watch maintenance
for more details).
Military
or 24 Hour Time:
When time is measured in 24-hour segments. To convert 12-hour time
to 24-hour time, simply add 12 to any p.m. time. To convert 24-hour
time to 12-hour time, subtract 12 from any time from 13 to 24.
Mineral
Crystal:
Watch crystal made from what is essentially a form of glass. More
scratch resistant than acrylic, a mineral crystal will however scratch
and is extremely difficult to polish.
Minute
Repeater:
A Complication on a watch that can strike the time in hours, quarters,
or seconds by means of a push piece.
Moon
Phase:
An indicator that keeps track of the phases of the moon. A regular
rotation of the moon is once around the earth every 29 days, 12
hours and 44 minutes. Once set, the moon phase indicator accurately
displays the phase of the moon.
Mother-of-Pearl:
Iridescent milky interior shell of the freshwater mollusk that is
sliced thin and used on watch dials. While most have a milky white
luster, mother-of-pearl also comes in other colors such as silvery
gray, gray blue, pink and salmon.
Movement:
The means by which a watch keeps time, often including the power
source. For example, a watch with mechanical movement uses a spinning
balance wheel powered by a tightly wound spring, whereas a watch
with quartz movement measures the vibrations in a piece of quartz
and often is powered by a battery.
Main
Menu
O
O-Ring:
O-rings are used to seal the backs of watches, which feature either
a press-in back or a screw on back. They ensure water resistance.
Usually also used on the winding stems of watches and in the winding
crowns to protect against the ingestion of water and dust. Normally
made from a rubber/plastic compound.
Main
Menu
P
Pedometer:
A device that counts the number of strides taken by the wearer by
responding to the impact of the wearer's steps.
Perpetual
Calendar:
A calendar complication that adjusts automatically to account for
different lengths of the month (30 or 31 days) and leap years. Perpetual
calendars, which can be powered by quartz or mechanical movements,
are programmed to be accurate until the year 2100.
Platinum:
One of the most rare precious metals, platinum also is one of the
strongest and heaviest, making it a popular choice for setting gemstone
jewelry and watches. It has a rich, white luster, and an understated
look. Platinum is hypoallergenic and tarnish resistant. Platinum
used in jewelry and watches is at least 85 to 95 percent pure. Many
platinum watches are produced in limited editions due to the expense
and rarity of the metal.
Power
Reserve Indicator:
A feature that shows when the watch will soon need a new battery
or winding. A battery reserve indicator on a quartz watch informs
the wearer when the battery is low. Often this is indicated by the
seconds hand moving at two or three-second intervals. Seiko's Kinetic
watches are quartz watches that do not have a battery (see Kinetic).
When a Seiko Kinetic needs to be wound, the seconds hand will also
move in two-second intervals.
Power
Reserve:
A measure of the amount of time a watch will run after being fully
powered or wound, with no additional power input. Normally, this
means when a mechanical watch is fully wound or a quartz watch has
a brand new battery. Many modern mechanical watches have a power
reserve of 40 hours. Power reserve also applies to battery-less
quartz watches, which may have power reserves from 40 hours to 6
months. On battery-operated quartz watches, the term is sometimes
used to refer to the expected battery life--typically 12 to 32 months.
Pulsimeter:
A scale on a chronograph watch for measuring the pulse rate.
Push-Piece:
Button that is pressed to work a mechanism. Push-pieces are usually
found on chronographs, striking watches, and alarms.
Main
Menu
Q
Quartz:
A caliber that uses the vibrations of a tiny crystal to maintain
timing accuracy. The power comes from a battery that must be replaced
about every 2-3 years. In recent years, new quartz technology enables
the watch to recharge itself without battery replacement. This power
is generated via body motion similar to an automatic mechanical
watch, or powered by light through a solar cell (Kinetic & solar-tech).
Main
Menu
R
Ratchet Bezel Ring:
A bezel ring that can either turn one way (counter clockwise) or
both ways and generally clicks into place.
Rattrapante
Chronograph:
The addition of a flyback hand (rattrapante) significantly increases
the potential uses for chronographs. It makes possible the measurement
of split second times or timing simultaneous events of unequal duration.
Register:
Another name for a subdial; this is usually a dial within the main
dial of a watch. The best example is possibly a chronograph where
there may be registers for the chronograph minutes and hours. Some
watches have registers with pointers showing the day and date.
Repeater:
A device that chimes the time when the wearer pushes a button. Some
repeaters, called "quarter repeaters" sound just the hours
and the quarter hours (by means of two different pitched tones);
others called "five minute repeaters", sound the hours,
quarters, and five minute periods after the quarter; and still others
called "minute repeaters", sound the hours, quarters and
minutes.
Retrograde:
Used to describe a pointer hand on a watch dial (often a subdial),
which returns to zero at the end of a prescribed period. For example
a watch may have retrograde date - in this case the hand moves up
a scale a day at a time, pointing to the current date - when it
reaches 31 it will spring back to 1
Rhodium
Plated:
Protective coating of metal with a thin layer of rhodium; hard,
brittle metal which does not oxidize and is malleable only when
red-hot.
Rose
(or pink) Gold:
A softly hued gold that contains the same metals as yellow gold
but with a higher concentration of copper in the alloy. A popular
color in Europe, rose gold in watches is often seen in retro styling
or in tricolor gold versions. Some 18k red gold watches achieve
their color from additional copper in the alloy.
Rotating
Bezel:
A bezel (the ring surrounding the watch dial) that can be turned.
Different types of rotating bezels perform different timekeeping
and mathematical functions.
Rotor:
The part of an automatic (or self-winding) mechanical watch that
winds the movement's mainspring. It is a flat piece of metal, usually
shaped like a semicircle, which swivels on a pivot with the motion
of the wearer's arm.
Main
Menu
S
Sapphire
Crystal:
Synthetic sapphire formed for use as the crystal of a watch. Extremely
scratch resistant (9 on the Moh scale), a sapphire crystal is the
material of choice for many watch collectors. The downsides are
that sapphire can chip at the edges if they protrude and can shatter.
Sapphlex
Crystal (Seiko Watches):
Highly scratch resistant crystal created by the fusion of sapphire
and mineral glass crystal.
Screw-Down
Locking Crown:
A crown that aids water resistance by sealing the crown to the case
of the watch. The seal is achieved by the matching of a threaded
pipe on the case with the crown's internal threads and gaskets,
while twisting the crown to lock it into place.
Second
Time Zone Indicator:
An additional dial that can be set to the time in another time
zone. It lets the wearer keep track of local time and the time in
another country simultaneously.
Self-Winding:
This term refers to a mechanically powered watch that is wound by
the motion of the wearer's arm rather than through turning the winding
stem (manual mechanical). In response to this motion, a rotor turns
and winds the watch's mainspring. Most automatic watches have up
to 36 hours of power reserve. If an automatic watch is not worn
for a day or two, it will wind down and need to be wound by hand
to get it started again.
Shock
Resistance:
As defined by the U.S. government regulation, a watch's ability
to withstand an impact equal to that of being dropped onto a wood
floor from a height of three feet.
Slide
Rule Bezel:
A rotating bezel, or ring, around the outside edge of the watch
case that is printed with a logarithmic scale and assorted other
scales and is used in conjunction with fixed rules of mathematics
to perform general mathematical calculations or navigational computations.
Solar
Powered:
A type of quartz movement where the batteries are recharged via
solar panels on the watch dial. They have a power reserve so they
can run even in the dark.
Solar Tech:
Solar powered quartz watch. This technology provides the accuracy
of quartz, without the inconvenience and cost of regular battery
changes.
Split
Second:
A feature on a chronograph that actually is two hands, one a flyback,
the other a regular hand. To time laps or different finishing times,
the wearer can stop the fly backhand independently while the regular
hand keeps moving.
Stainless
Steel:
An extremely durable metal alloy (chromium is a main ingredient)
that is virtually immune to rust, discoloration, and corrosion;
it can be highly polished, thus resembling a precious metal. Stainless
steel is often used even on case backs on watches made of other
metals and is the metal of choice used to make high quality watchcases
and bracelets. It is also hypoallergenic because it doesn't contain
nickel.
Sterling
Silver:
A precious metal. Sterling refers to silver that is 92.5 percent
pure. The silver fineness should be stamped on the metal, sometimes
accompanied by the initials of a designer or country of origin as
a hallmark. A protective coating may be added to prevent tarnishing.
Stopwatch:
A watch with a seconds hand that measures intervals of time. When
a stopwatch is incorporated into a standard watch, both the stop
watch function and the timepiece are referred to as a "chronograp".
Strap:
A watchband made of cloth, rubber, leather or other non-metal material.
Subdial:
A small dial used for any of several purposes, such as keeping track
of elapsed minutes or hours on a chronograph or indicating the date.
Swiss
A.O.S.C. (Certificate of Origin):
A mark identifying a watch that is assembled in Switzerland with
components of Swiss origin, primarily used in Bedat watches.
Main
Menu
T
Tachometer (Tachymeter):
Instrument for measuring speed or units. In watch making, a timer
or chronograph with a graduated dial on which speed can be read
off in kilometers per hour or some other unit (see timer).
Tank
Watch:
A rectangular watch with heavier bars on either side of the dial.
Inspired by the tank tracks of World War I and first created by
Louis Cartier.
Tantalum:
A metal with a texture similar to titanium, but a color similar
to gold. Used by Omega for the gold-like trim on certain titanium
watches. Many of these watches are also available in titanium with
real gold trim.
Telemeter:
A watch function that finds the distance of an object from the wearer
by measuring how long it takes sound to travel the distance. Like
a tachometer, a telemeter consists of a stopwatch function and a
special on the dial of a chronograph.
Timer:
Instrument used for registering intervals of time (duration, brief
times), without any indication of the time of day.
Titanium:
A "space age" metal, often having a silver-gray appearance.
Because it is 30 percent stronger and nearly 50 percent lighter
than steel, it has been increasingly used in watch making, especially
sport watch styles. Its resistance to salt water corrosion makes
it particularly useful in diver's watches. Since it can be scratched
easily, some manufacturers use a patented-coating to resist scratching.
Titanium is also hypoallergenic.
Tonneau
Watch:
A watch with a barrel-shaped watchcase and two convex sides.
Totalizer:
A mechanism that keeps track of elapsed time and displays it, usually
on a subdial on the watch dial. Same as a "recorder" or
"register". The term "totalizer" can be used
more generally to refer to any counter on a watch.
Main
Menu
U
Unidirectional Rotating Bezel:
An elapsed time rotating bezel, often found on divers watches, that
moves only in a counterclockwise direction. It is designed to prevent
a diver who has unwittingly knocked the bezel off its original position
from overestimating his remaining air supply. Because the bezel
only moves in one direction, the diver can err only on the side
of safety when timing his dive. Many are ratcheted, so that they
lock into place for greater safety.
UTC:
Universal Time Coordinated. A universal time based on the Greenwich
Meridian used by the military and in aviation. Greenwich Mean Time
(GMT) can be considered approximately equivalent to Universal Time
Coordinated (UTC). GMT as such is now obsolete however, being replaced
by UTC. Using this timezone/standard avoids errors and problems
associated with different time zones and summer times operational
in different countries.
Main
Menu
W
Water Resistance:
Describes the level of protection a watch has from water damage.
See the "water resistance" section for a description of
the different levels.
Waterproof:
The ability to completely exclude the possibility of water entering
into any working portion of a watch. According to the Federal Trade
Commission, no watch is fully 100 percent waterproof and no manufacturer
that sells watches in the U.S. may label any of their watches "waterproof."
The FTC demands that watches only be referred to as "water
resistant."
Winding
Stem:
The button on the right side of the watchcase used to wind the mainspring.
Also called a "crown."
Winding:
Operation consisting of tightening the mainspring of a watch. This
can be done by hand (by the crown) or automatically (by a rotor,
which is caused to swing by the movements of the wearer's arm).
World
Time Dial:
A dial, usually on the outer edge of the watch face, which tells
the time up to 24 time zones around the world. The time zones are
represented by the names of cities printed on the bezel or dial.
The wearer reads the hour in a particular time zone by looking at
the scale next to the city that the hour hand is pointing to. The
minutes are read as normal. Watches with this feature are called
"world timers."
Main
Menu
Y
Yacht Timer:
A countdown timer that sounds warning signals during the countdown
for a boat race.
Main
Menu
